LIFT GATES - Anthony Magnum RailTrac Heavy Duty
back to top
Quality Features
Dual Pump and Motor Hydraulic Drive System
Twin pumps, motors, and solenoids handle the work with half the effort required of a typical single-pump tailgate system, resulting in a longer and more dependable service life.
ZLC™ Zero Leak Concept
Uses machined fittings, SAE "O" ring and JIC hydraulic connectins, along with factory installed -70 degrees low pour hydraulic fluid. The results is long, trouble-free service with no aggravating and costly leaks.
Lifetime Warrantied Service-Free™ Sliders
Inside the vertical tracks there are no rollers or roller bearings to wear or replace. This can mean saving thousands of dollars over the life of the Liftgate®.
Self-Aligning Cylinder Attachment Ends
Platform lift cylinders are mounted on self-aligning swivel ends that prevent sideloading of cylinder pistons and internal cylinder wall scoring.
Service-Free Bushings
Used at critical pivot points, these bushings extend pin and arm life and eliminate routine lubrication.
Bolt-on Switch Box
The switch box housing is easily removable for quick and easy, efficient servicing or replacement. Inside, heat-shrink siliconed wire connections seal out moisture and stainless steel terminals provide extra corrosion protection.
back to top
Standard Features
Tail Lights
Prewired and pigtailed for easy hookup.
Galvaneal Power Unit Enclosure
Separate vented battery compartment for two 12 volt batteries.
Marine-Duty Sealed Toggle Switch
Operates reliably under all types of weather conditions.
Pressure Compensated Flow Valve
Provides constant and controlled lowering speed of the platform, loaded or unloaded.
Closed Hydraulic System
Provides positive protection against outside dust, dirt, and moisture; protects against hydraulic contamination.
Yellow Di-Chromate Plated Pivot Pins
Resist corrosion to increase service life.
Heat-Shrink Siliconed Wire Connections
Prevent electrical failure by sealing out moisture at all electrical connections and stainless steel terminals provide extra corrosion protection.
Hard Chrome Plated Piston Rod
Helps keep exposed surface free of rust and contamination to protect seals and extend cylinder life.
Relief Valve
Prevents overloading during lifting cycle.
Factory Installed Hydraulic Fluid
Prevents contamination during field installation and ensures proper SAE fluid.
Powered Platform
Toggle-switch controlled hydraulic system provides easy opening and powered closing.
Powder Coated Finish
Provides attractive, long-life protective finish.
Circuit Beaker
Protects truck wiring and power system in the event of a "dead short."
Factory Assembled, Tested, and Energized
Assures consistent, high-quality performance standards.
E-Z Mount Installation
Shipped completely pre-assembled for fast, clean, easy installation.
Cut-Off Switch
Protects valuable liftgate equipment from unauthorized use or vandalism.
Exclusive 2 + 1 Warranty
2 years on mechanical components; 1 year on the hydraulic system, parts, and labor.
back to top
Available Models, Platforms and Capacities
| Model | Lifting Capacity (lbs.) | Bed Height Min-Max |
Platform Load Area and Ramp |
Shipping Weight (lbs.) |
| MRT-3500-SF | 3,500 | 38"-58" | 80" x 60" + 12" ramp w/pop-up cart stop | 2,353 |
| MRT-3500-SF | 3,500 | 38"-58" | 80" x 72" + 12" ramp w/pop-up cart stop | 2,413 |
| MRT-3500-SF | 3,500 | 38"-58" | 80" x 84" butt edge w/o ramp | 2,465 |
| MRT-4500-SF | 4,500 | 38"-58" | 80" x 60" +12" ramp w/pop-up cart stop | 2,412 |
| MRT-4500-SF | 4,500 | 38"-58" | 80" x 72" + 12" ramp w/pop-up cart stop | 2,452 |
| MRT-4500-SF | 4,500 | 38"-58" | 80" X 84" butt edge w/o ramp | 2,514 |
| MRT-5500-SF | 5,500 | 38"-58" | 80" X 60" + 12" ramp w/pop-up cart stop | 2,463 |
| MRT-5500-SF | 5,500 | 38"-58" | 80" x 72" + 12" ramp w/pop-up cart stop | 2,503 |
| MRT-5500-SF | 5,500 | 38"-58" | 80" x 84" butt edge w/o ramp | 2,565 |
| MRT-6500-SF | 6,500 | 38"-58" | 80" x 60" + 12" ramp w/pop-up cart stop | 2,504 |
| MRT-6500-SF | 6,500 | 38"-58" | 80" x 72" + 12" ramp w/pop-up cart stop | 2,544 |
| MRT-6500-SF | 6,500 | 38"-58" | 80" x 84" butt edge w/o ramp | 2,606 |
back to top
Options
- Power Down On Demand (switched to Power Down "on demand" by operator)
- Auxiliary hand pump
- Pump and motor extension kit
- Bed height stored model
- Hand-held control with plug and socket
- 16" aluminum retention ramp
- Header kit
- 102" wide models
- Hose and wire channel mounting kit
- Trailer wiring kits
back to top
Mounting Requirements
